|
|
Post by 81camaro383 on Jan 18, 2011 20:03:18 GMT -5
ok so now im in the middle of re wiring the car and and have this box i want to be able to remove it and still run with out it the only problem is how do u hook the 2 step wire to the plug in that is hooked to the box do i make a wire that comes off of the trans brake wire because thats where it should be hooked up at if u hook the wire to ur plug then the box wont come out ....
|
|
|
|
Post by jparker1229 on Jan 18, 2011 20:11:11 GMT -5
So your trying to remove the 2 step and still use the transbrake ?
|
|
|
|
Post by ajcasini on Jan 18, 2011 20:17:47 GMT -5
Are you are trying to use the box and then remove the box to use the t-brake and 2-stp to leave off the bootm?
If so what I did was used a weatherpack connector to plug into box and then had a jumper plug to put in place of the box that connected the two-step to the t-brake wire.
If your box does not have a 2-step connector on it then you will need to wire the 2-step to the same post as the t-brake.
What box do you have?
|
|
|
|
Post by 81camaro383 on Jan 18, 2011 20:30:59 GMT -5
yea im going to try to bottom bulb race to and run a box i have a 4 flat plug in and a dedenbear cross over i have the dummy plug figured out but im not sure on where and how my two step is going to work if i dont have it on the box plug ....i got the the transbrake and the line lock tied together on the box plug and it still be removed
|
|
|
|
Post by triplenickel on Jan 18, 2011 21:10:11 GMT -5
I think I understand what your asking. Wire your t-brake & 2step wires together on the connector that stays in the car. Then have a dummy connector to plug into the connector on the car that will jump the wire from your button to the t-brake/2step wires.
|
|
|
|
Post by 81camaro383 on Jan 18, 2011 21:13:50 GMT -5
yep and i can still tie my line lock on the same wire that stays in the car too b/c my brother told me the box should keep everything active until the delay box releases it all
|
|
|
|
Post by 81camaro383 on Jan 18, 2011 21:16:41 GMT -5
and the other thing is the wire that is going to my delay box that says switch threw the plug in the car im taking it over to the wires going to the 2 step line lock and transbrake that way it will get power when box is gone
|
|
|
|
Post by triplenickel on Jan 18, 2011 21:22:53 GMT -5
How many terminals does your delay box have & how are they labeled? Some boxes have a seperate terminal for linelock.
|
|
|
|
Post by 81camaro383 on Jan 18, 2011 21:38:53 GMT -5
I've got five spots on my delay box 1 transbrake 2 switch 3 line lock 4 ground 5 12 volt ......thats why I'm going to wire those two together my plug is a four flat type....
|
|
|
|
Post by butterbean on Jan 19, 2011 0:04:43 GMT -5
Man I love this site, Nickel got the LS-7 joke  |
|
|
|
Post by adamsvega on Jan 19, 2011 6:49:31 GMT -5
i wired two buttons one direct and one through the plug .so when i pull the box the other button still has my reverse and t/b and throttle control on it .
so the steering wheel button is always active .also put a momentary switch on dash and a plug jumper on colum switch ....for true foot brake class i have to loosen harness and reach across to hit rev. to stop the whinners from saying im using a t/b .
with double buttons i never get mixed up in class racing its always left hand and box is always rt hand on shifter bracket button.
with cross talk in super everywhere around hear the double hit feture of my sponsors biondo box never helped me (redlite) hell i asked Sal if they could switch it to take the slower one . after one yr of data i lost 3 races i could not have lost and only one was close enough to matter the other way being the slower car most of the time it was to close to help
|
|
|
|
Post by ajcasini on Jan 19, 2011 18:23:52 GMT -5
I have the same box in my car and have the tbrake and 2 step wired together. As for the line lock I wired it direct to the box through the connector. On my jumper I wired the line lock to the 2-step and brake wire along with the 12v hot coming from the button.
If you use the line lock to do your burnout be sure to have a toggle swith intterupting the wire going to your connnector when bottom bulb racing.
|
|
|
|
Post by 81camaro383 on Jan 19, 2011 19:25:37 GMT -5
ok i got an up date i was out in the car tonight and wired the 2 step with line lock to test it and the 2 step held power until the box reach the timer so i now have it figured out and the help is great on this site when i get my 2 speed ill finish the car
|
|
